“The foundation of your home is your walls. The weather out there will not be good for your house’s exterior walls, so you need to pay special attention to them. It isn’t enough to paint your wall to make it waterproof. After dealing with rain, snow, wind, dust, and heat, the paint will start peeling off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
“The outer part of your home’s wall is usually covered with a lot of dust and dirt from the air. To ensure the efficiency of the process, you need to clear off the debris and dust thoroughly. The dirt and debris should be cleaned with a broom, brush, or sandpaper. Then use a power washer to wash it off.”
Step 3: Check out for the cracks and fill them up
“Cracks and holes can develop on your walls over time. Follow up the cleaning process with a thorough look at the cracks and holes on your wall to make sure it’s waterproof. Just fill them up with cement.”
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
The mixture of cement penetrated inside the cracks and seals them. Remove all the loose cement from the wall before applying the cement.
Step 4: Add a layer of cement waterproofing sealer
If you want to make your wall waterproof, you need to apply the cement waterproofer. After applying the cement in the crevices, let it dry, then apply the waterproof paint seal for the exterior walls. Allow it to become dry after that.
Step 5: Pick the right water-proofer
There are many products available in the market. You have to pick the one that goes with the wall you have. Pick the water-proofer based on whether it is a concrete wall or a silicate-based one.
A silicate-based concrete sealer is one of the options you can choose from. Pick a plaster waterproof Additive that will add strength to your walls.
Step 6: Apply the water-proofer
Use a brush or roller to apply the water-proofer to the walls. Give a thin coat if you want to apply more than one layer. Add the second coating after the first one is dry.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layers, you need to use a tar-based pitch after the drying of the cement waterproofener. You should apply it on your wall.
After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of the walls.
Step 8: Consider adding gravel
To lay the drainage pipes you need a proper base below the footer. The drainage pipes will get adequate support from a 34-inches gravel base. Gravel is long lasting and provides enhanced protection.
You need to lay the drainage pipe-cover along with the gravel. If you want to back-fill the gravel, level it near the footer. Make sure the pipe is covered for at least 3 inches.
Step 9: Add a fabric barrier
Attach the fabric barrier to the pipe. Ensuring that a fabric barrier is in place will prevent the formation of dirt. Then back-fill the trench and build the top of the dirt relatively high and let it settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,
Good waterproof gives your home a new life and strength to deal with weather-related issues. Magicrete can help you find good solutions for your walls. At a very low and affordable price, Magicrete can provide you proper weatherproofing.
“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s”